 |
 |
 |
 |
 |
|
|
|
Printable version
Design Features
Tubular Derrick
The 10"x16" tubular derrick construction is considerably lighter weight than traditional lattice-type derricks, while providing superior strength.
Feed System (patented)
Hydraulic cylinder/sliding gear track design, provides tremendous power (20,000 lbs. pullback), requiring less maintenance than conventional system with chains and sprockets or cables and sheaves.
Top Head Drive
A variable 2-speed/torque, floating head provides smooth operation and helps the operator recognize specific formations while drilling.
Top head hydraulically slides to the side, (off-hole) for convenience of setting casing.
Split Centralizer Table
Centralizer base plate is split in half, rear half stationary, and the front half swings out to accommodate casing and tools. Also includes a manual drill rod holding wrench and hydraulic breakout wrench.
Hydraulic Swing Jibs
A standard 8,000 lbs. main winch and jib to position over the hole or swing to side for efficient casing and tool handling. Rig designed for maximum 8" finished bore hole.
back to top
|
|
Mounting
Rubber track all-terrain carrier
IHI-70 (224HP)
Hydraulics
Two axial piston hydrastatic pumps power the vehicle tracks and tophead or mud pump mud independently. An axial piston load sense pump powers the feed, winch, auxiliary and set-up functions. A cast iron gear pump provides the charge pressure and flow to circulate fresh oil into the hydrastatic pump circuits.
Air Compressor
Auxiliary air connections (only)
Cooling
Hydraulic oil cooler mounted on deck
Derrick
10"x16" tubular derrick construction
23' 6" overall length
15' top head travel
(No derrick crown load)
Feed System (patented)
Cylinder feed through gear track design
Pullback 20,000 lbs.
Pulldown 11,000 lbs.
Travel Speed Up 0 to 75'/min.
Down 0 to 135'/min.
Drill Feed 29'/min.
back to top
|
|
Top Head Rotation
2 motor combination planetary/spur gear
2 speeds/torques
0 to 150 rpm, 52,000' lbs. torque
0 to 200 rpm, 39,000' lbs. torque
Main Winch
Hydraulic power with integral brake
Rope Capacity 400' of 3/8" cable
Lift Capacity 8,000 lbs. single line (bare drum)
Speed 78'/min. (bare drum)
Jib Boom
Manual swing for main hoist line
Controls
Left hand mounted, functionally grouped gauges and controls
Leveling Jacks
1 front-mounted 36" stroke leveling jack and
2 rear-mounted 36" stroke leveling jacks with
independent controls
Split Centralizer Table
Split centralizer for rod handling and up to 8". Includes manual pipe holding wrench and hydraulic breakout wrench.
Hydraulically Tilting Rod Box
Holds 30 pieces of 3" OD x 10' drill rod
or
25 pieces of 3 1/2" x 10' drill rod.
|
|
Overall Length
24' 3"
Overall Height
Derrick up - 26'
Derrick down - 9' 9"
Overall Width
8' 4"
back to top
|
|
(at additional cost)
Rod Handling
300' of 3" or 250' of 3 1/2" rod handling system
Main Winch
2,000, 4,000, 8,000 (standard), 12,000 lbs.
DHD Lubricator
7-gallon capacity
Water Injection
FMC Bean pump w/9 GPM capacity
Mud Pumps
a. 3x4 centrifugal w/mechanical seal
(300 GPM/230 PSI)
b. 5x6 piston-type hydraulic driven
(200 GPM/300 PSI)
Grout Pump Assembly
Geo-Loop YP1 compact grouter, Deck mounted hydraulically lowered to the working area
Night Lighting System
3 halogen lights mounted on derrick and above control panel
|
|
|
 |
|
 |
 |
|
1414 Bates Street • Indianapolis, IN 46201 U.S.A.
Telephone: +1 317 231 2250 • Fax: +1 317 266 8426
Toll Free: (800) 942-3388 •
sales@laibecorp.com
|
|
|
