 |
 |
 |
 |
 |
|
|
 |
Printable version
Design Features
Low Profile Carrier
4x8 (all wheel drive), short wheelbase (236"), deluxe aluminum center mount one-man cab, aluminum wheels and fuel tanks (250 gallon fuel capacity).
Feed System (patented)
Powerful direct coupled, hydraulic cylinder driven feed system. Eliminates use of chains, cables, sprockets and sheaves (95,000 lbs. pullback/34,000 lbs. pulldown).
Drill Pipe Storage and Control System (patented)
Totally automated handling, positioning and storage of all drill pipe, on board.
Drill/Truck Diesel Power
Single power source with exclusive Versa-Drill power distribution gear box/pump drive, provides direct coupled thru-drive to power rig hydraulics and air compressor.
Air Compressors
Ingersoll-Rand self-contained modules (900/350 or 1250/350), environmentally protected, 145° ambient cooling, lower noise levels.
Casing Handling
Retractable split centralizer table, sliding off hole top-head and swing jib that centers directly over the hole, providing easier handling of up to 20" diameter Range II casing.
* Available with optional Range III casing handling assembly (see under options)
back to top
|
|
Mounting
HME custom carrier 4x8
CAT C-18 (630HP)
Power Distribution
Drill/truck single-power source with exclusive Versa-Drill power distribution gearbox/pump drive, provides direct coupled thru-drive to power rig hydraulics and Ingersoll-Rand screw air compressor
Hydraulics
Rotation is a closed loop circuit powered by a variable displacement piston pump
Feed, winch, auxiliary and set-up functions are powered by 4 axial piston load sense pumps
105-gallon reservoir with 10 micron in-tank return filter and 10 micron pressure filters for closed-loop pumps
Air Compressors
900 CFM/350 PSI self-contained module
or
1250 CFM/350 PSI self-contained module
All compressor modules are direct driven with drive shaft from power distribution box accompanied by hydraulic chassis clutch control (controlled at drill console)
Derrick
12" x 28" tubular derrick construction
48' overall length
36' head travel
(No derrick crown load)
Feed System (patented)
Direct coupled, cylinder driven
Pullback 95,000 lbs.
Pulldown 34,000 lbs.
Travel Speed:
Up 0 to 180'/min.
Down 0 to 230'/min.
back to top
|
|
Top Head Rotation
Standard high performance 3-speed/ torque planetary, spur gear top head
High Torque 8,100 ft.-lb. @ 132 RPM
Mid Torque 6,200 ft.-lb. @ 173 RPM
Low Torque 4,280 ft.-lb. @ 250 RPM
Main Winch & Jib Boom
12,000 lb. (standard) hydraulic powered main winch, includes hydraulic jib boom with 180° radius swing and 40" extension 18,000 lb. main winch (optional)
Rope Capacity 220' of 5/8" rotation resistant cable
Lift Capacity 12,000 lb. single line (bare drum), 18,000 lb. (optional)
Speed 104'/min. (bare drum)
Controls
Electro/hydraulic console control panel with functionally grouped gauges and controls with twin fold-up aluminum platforms (standard)
Leveling Jacks (6 point leveling system)
2 front-mounted 36" stroke jacks
2 mid-mounted 48" stroke jacks
(behind cab)
2 rear-mounted 36" stroke leveling jacks
(all with independent controls)
Centralizer
Retractable hydraulic split centralizer table including hydraulic breakout wrench and air operated holding wrench. Table opening will accommodate up to 20" casing
Automated Drill Pipe Storage & Handling System (patented)
Automated drill pipe storage and control system
stores and positions 25 pieces (500') of
4 1/2" x 20' drill pipe (only) |
|
Overall Length
Derrick Down - 48'
Overall Height
Derrick up - 42'
Derrick up w/tophead at full stroke - 61.5'
Derrick down - 12' 9"
Overall Width
102"
Range III Casing Assembly
Provides the ability to handle up to a maximum 47,500 lbs. of Range III casing
Auxiliary Hoist
2,000 lb. auxiliary hydraulic winch with swing jib
DHD Lubricator
7-gallon capacity (electric)
Water Injection
a. *FMC Bean pump w/25 GPM capacity
b. *CAT w/25 GPM capacity
*Optional foam pulse pump (available)
* Mud Pumps
3 x 4 centrifugal w/mechanical seal
(300 GPM/230 PSI)
5 x 6 Piston type (hydraulic powered)
5 1/2 x 8 piston type (hydraulic powered)
*Rig or skid-mounted
Night Lighting System
9 halogen lights functionally mounted on drill rig
* Hammer Holder(s)
a. 6" Hammer holder
b. 8" Hammer holder
c. 10" Hammer holder
d. 12" Hammer holder
*Any combination of, no more than 3
Stabilizer Chute
Up to 9" x 15' stabilizer chute mounted on rig
|
|
Model
HME Custom carrier 4x8
Wheelbase
236"
GVWR
86,000 lb.
Dual Front Axle Suspensions (Twin Steer)
Axle Rating 40,000 lb.
Suspension 40,000(ea.) lb. leaf
Rear Axle Suspension
Axle Rating 46,000 lb. tandems
46,000 lb. spring-mounted walking beam
*Driver controlled locking axles
Engine
CAT C-18 (630 HP)
Transmission
Manual, 10-speed
Frame
12 5/8" x 3/8" x 3 1/4"
11 7/8" x 5/16" x 2 7/8" C-channel
Brakes
Air brake system with anti-lock brakes
Clutch
Eaton self-adjusting clutch
Fuel Tank Capacity
250 gallons (total)
Other Specifications
Alcoa aluminum wheels
Aluminum fuel tanks
Brushed aluminum mirrors
Power steering
Power brakes
Jacobs engine brake
AM/FM radio w/CD player
Air conditioning
Diesel fired engine heater
Water preheater |
|
back to top |
 
 
 
|
|
1414 Bates Street • Indianapolis, IN 46201 U.S.A.
Telephone: (317) 231-2250 • Fax: (317) 266-8426
Toll Free: (800) 942-3388 •
sales@laibecorp.com
|
|
|
